Plastic Waste Processor – PWP Registration under CPCB

As indicated by the new warning of the Central Pollution Control Board (CPCB) under the Ministry of Environment, Forest and Climate Change (MoEF&CC) mandated Plastic Waste Processor – PWP registration under CPCB. The enlistment should be possible on the Concentrated Broadened Maker Obligation (EPR) entry and conform to the EPR. As per the altered rules, under Section 4, Stretched out Maker Obligation is given to the Makers/Merchants/Brand Proprietors (PIBOs) and plastic processors engaged with waste to energy, waste to oil, recycling and industrial composting.

EPR Authorisation for Plastic Waste Processors is represented under Plastic Waste Management Rules, 2016. Processors should record an Authorisation application to the incorporated entryway of the CPCB with the approved archives. When the Authorisation application is presented, the concerned PCC or SPCB really take a look at the application to approve and examine the reports, following which the processor is given the Authorisation.

The enrollment application should be handled in no less than 15 days, inside which the contamination control specialists will either concede or dismiss the authorisation. On the off chance that the application isn’t handled inside the ordered time, the enrollment will be produced consequently for the Plastic Waste Processor.

Documents required for acquiring EPR Authorisation

• • The authorisation/certification from the respective/applicable state authority for the operating plastic processing unit. The documents required areas follows:
    • TIN details;
    • PAN details;
    • Incorporation certificate;

Assuming the archives ordered to be presented by the Plastic Waste Processor are found to be manufactured whenever, the enlistment will be viewed as invalid and void. Aside from this, assuming that the PWP is viewed as abusing any arrangements of the enlistment or the rules commanded, the notification for a similar will be given by the SPCB/PCC.

To guarantee fair possibilities, the Plastic Waste Processor will be permitted to introduce their side in something like fifteen days from the date of notice prior to settling on a ultimate conclusion on the retraction or suspension of the PCC/SPCB. The choice for abrogation will be imparted inside ten working days after the conference. Executive of Pollution Control Committee/State Pollution Control Board will at last request that the power settle on a decision on wiping out or suspension.

CTE (Consent to Establish)is obtained by Plastic Waste Processors before the handling unit is laid out under the Air and Water (Prevention and Control of Pollution) Act. However, CTO (Consent to Operate)is acquired after the processing unit is established and is ready to start the manufacturing process under the same Acts.

The certification process for both assent testaments is indistinguishable. The authorisation structure is submitted by means of the concerned Union Territory PCC/the SPCB with the necessary records, trailed by a survey of an application. When the records are examined, on account of the CTO, an administration official of state specialists directs a site investigation and makes the report in like manner. The assent testament is conceded to the Plastic Waste Processor after investigating the report.

Documents required for consent certificate

To get authorisation for natural compliances, the Plastic Waste Processor needs to procure general permits to operate and authorisation from the concerned administrative specialists. A couple of these licenses are: –

• • • PAN card
    • Address proof such as
      • Passport
      • Election card or Voter Identity card
      • Ration card
      • Driving license
      • Electricity bill
      • Telephone bill
      • Aadhaar card
    • Residential proof such as
      • Bank statement
      • Electricity bill
      • Telephone bill
      • Mobile bill
    • GST registration certificate
    • MOA (Memorandum of Association)
    • AOA (Article of Association)

To lay out their assembling units, Plastic Waste Processors must list their business under Factories Act. According to the act, processors are ordered to get an industrial facility permit, which the Chief Inspector of the Labour Commissioner Organisation approves after examining the Plastic Processing site.

Documents needed by Plastic Waste Processor

For the factory license, Plastic Waste Processors require the following documents: –

To lay out a handling unit, the Plastic Waste Processor is ordered to gain Ministry of Micro, Small and Medium Enterprises (MSME) registration. PWP should enroll through the MSME’s unified online portal with the Authorised documents.

Documents needed for MSME registration:-

The enrollment connecting with the foundation or transboundary or cross country development of hazardous waste that includes the establishing Plastic Processor Unit is regulated under The Hazardous Wastes (Management, Handling and Transboundary Movement) Rules, 2008. For authorisation, the PWP must apply under Form 1 to the concerned SPCB’s site to secure the authorisation.

Documents required for submission:-

The Documents which are Compulsory while Applying for Hazardous Waste Authorisation are: –